Datasheet
Close
Specifications
Others
Package 1 bare product quantity
1
Unit type of package 1
PCE
Number of units in package 1
1
Package 1 height
0.005 cm
Package 1 width
0.015 cm
Package 1 length
0.015 cm
Package 1 weight
340 g
Frequently Asked Questions
hide show
Yes, the PSMA4 range is backward compatible with the PSMA2 and SD100 range of smoke alarms.
For further information please visit www.pdl.co.nz
For further information please visit www.pdl.co.nz
The dust inside the smoke alarms can cause a continuous beep.
Please follow the regular maintenance check to avoid this.
Vacuum the smoke alarms using a soft brush attachment-
Keeping your smoke alarm free of dust particles, dirt, kitchen grease or cobwebs will help you reduce false alarms and ensure any smoke can easily reach the internal sensing chamber.
Clean and wipe down around unit-
Clean around the smoke alarm unit and remove any insects or other contamination which may have occurred. Spray bug repellent on a cloth and wipe the ceiling around the smoke alarm to act as a future bug deterrent. Clean every 3-6 months to mitigate insect ingress.
ALWAYS TEST THE SMOKE ALARM AFTER CLEANING.
Attached is the Clipsal smoke alarm troubleshooting guide for more info.
Please follow the regular maintenance check to avoid this.
Vacuum the smoke alarms using a soft brush attachment-
Keeping your smoke alarm free of dust particles, dirt, kitchen grease or cobwebs will help you reduce false alarms and ensure any smoke can easily reach the internal sensing chamber.
Clean and wipe down around unit-
Clean around the smoke alarm unit and remove any insects or other contamination which may have occurred. Spray bug repellent on a cloth and wipe the ceiling around the smoke alarm to act as a future bug deterrent. Clean every 3-6 months to mitigate insect ingress.
ALWAYS TEST THE SMOKE ALARM AFTER CLEANING.
Attached is the Clipsal smoke alarm troubleshooting guide for more info.
GLOBAL / LOCAL RELAY SETTING
Both the 755PSMA2 and 755RLPSMA2 smoke alarms have a ‘Global / Local’ switch located on them (see the diagram below). This switch is only used for operation with the 755RB
relay mounting base.
• When the ‘Global / Local’ switch is set to ‘Local’, only activation of the physically connected alarm will cause the relay to operate.
• When the ‘Global / Local’ switch is set to ‘Global’, activation of any smoke alarm that is interconnected with the base causes the relay to operate.
• The default setting is ‘Global’.
For further information, please visit:
http://www.clipsal.com/Trade/Products/ProductDetail?catno=755PSMA2
http://www.clipsal.com/Trade/Products/ProductDetail?catno=755RLPSMA2
http://www.clipsal.com/Trade/Products/ProductDetail?catno=755RB
Both the 755PSMA2 and 755RLPSMA2 smoke alarms have a ‘Global / Local’ switch located on them (see the diagram below). This switch is only used for operation with the 755RB
relay mounting base.
• When the ‘Global / Local’ switch is set to ‘Local’, only activation of the physically connected alarm will cause the relay to operate.
• When the ‘Global / Local’ switch is set to ‘Global’, activation of any smoke alarm that is interconnected with the base causes the relay to operate.
• The default setting is ‘Global’.
For further information, please visit:
http://www.clipsal.com/Trade/Products/ProductDetail?catno=755PSMA2
http://www.clipsal.com/Trade/Products/ProductDetail?catno=755RLPSMA2
http://www.clipsal.com/Trade/Products/ProductDetail?catno=755RB
Red LED flashing once every 40 seconds with one audible beep is a low battery warning.
Replace the 9 V d.c. battery with a new one. (It is recommended to replace the battery annually)
To snooze a low battery beep for 10 hours, press the Test/Hush button for 3 seconds.
And if the smoke alarm continues to beep once every 40 seconds after a new battery replacement,
Replace the 9 V d.c. battery with a new one. (It is recommended to replace the battery annually)
To snooze a low battery beep for 10 hours, press the Test/Hush button for 3 seconds.
And if the smoke alarm continues to beep once every 40 seconds after a new battery replacement,
- Unclip the alarm from the base.
- Remove the new battery.
- Press and hold the test button for 20 seconds.
- Replace the new battery and clip it back to the base.